风管集中加工容易出现哪些特点？
2018-09-12
（1）风管集中化加工的优势特点
(1) advantages and characteristics of centralized processing of wind pipes
①减少材料损耗，降低加工成本：风管集中批量预制加工，能够做到“量体取材”，避免了人工操作时材料乱截、大材小用等现象，使用材料，同时降低人工成本。
(1) Reduce material loss, reduce processing costs: centralized batch prefabrication of air duct, can achieve "volume material", avoid the manual operation of materials in disorder, large materials and small use of such phenomena, the maximum use of materials, while reducing labor costs.
②缩短现场工期：集中加工能形成流水线生产作业，有效提高人员及材料效率，缩短生产周期，提高材料利用率。因集中加工一般在站外加工，所以在现场机电工作面还没有形成的时候，即可提前在场外进行，对于工期紧、任务重的机电安装工程，能有效节省大量现场工作时间和交叉作业时间，节约现场的加工场地，改善地铁施工场地不足的问题。
(3) Improving the quality by a large margin: The factory processing air duct realizes the modularization, intellectualization, standardization and high efficiency of production, greatly reduces the material error of air duct and improves the appearance quality. (4) Easy overall planning and management: Centralized processing can avoid the good and bad scattered processing capacity of each construction team, and can avoid the problem of inconsistent air duct products caused by different processing technology and standards. At the same time, centralized processing can better control the installation site of safe and civilized construction, to avoid the phenomenon of semi-finished products piled up in disorder.
（2）风管集中化加工的缺点
(2) disadvantages of centralized air duct processing
①风管集中加工后，各站施工队将同时与同一加工厂家进行合作，这将给施工方与加工方在沟通、进度等方面带来挑战，遇到施工高峰期时，如前期准备不足，所有站的生产压力集中到同一厂家，可能会对施工造成影响。
(1) After centralized air duct processing, the construction team of each station will cooperate with the same manufacturer at the same time, which will bring challenges to the construction party and the processing party in communication, progress and other aspects. In the peak period of construction, if the preparation is insufficient, the production pressure of all stations will be concentrated in the same manufacturer, which may affect the construction.
②准备周期长、初期投入大：集中生产如由项目部自筹（或某一施工队自筹），其厂房筹建、场地规划、方案制定等周期较为漫长；初期设备成本大，如不能形成一定规模，难以收回成本。
(2) Long preparation period and large initial investment: if centralized production is self-raised by the project department (or a construction team), the period of workshop preparation, site planning, scheme formulation is relatively long; if the initial equipment costs are large, it is difficult to recover costs if it can not form a certain scale.
③成品运输问题：集中加工后需将风管成品运输各站，这将带来如下影响：
(3) Transportation of finished products: After centralized processing, finished air ducts should be transported to various stations, which will bring the following effects:
a. 风管成品受压后易变形（且不易修复），在运输中装卸车、进站经常会产 生碰压，影响风管美观，甚影响风管质量。
A. The finished air duct is easy to deform (and not easy to repair) after compression. In transportation, loading and unloading trucks and stops often produce impact pressure, affecting the beauty of air duct, and even affecting the quality of air duct.
b. 风管成品比原材料占用的空间大很多，因此会增加运输次数，提高运输 成本，同时因地铁施工一般在市区，如遇限行区域施工时只能晚上进料，给施工带来不便。
B. The finished air duct occupies much more space than the raw material, so it will increase the frequency of transportation and increase the cost of transportation. At the same time, because the subway construction is generally in the urban area, such as restricted traffic area construction can only feed at night, which brings inconvenience to the construction.
有了济南通风管道加工上面的小总结，希望对广大客户有所帮助，如果有什么不理解的或者寻求帮助的请点击我们的网站：http://www.jinanxinlian.com或者来电咨询，我们会尽全力为您解决!
With Jinan ventilation duct processing above a small summary, I hope to help the majority of customers, if there is any incomprehension or seek help, please click our official website: http://www.jinanxinlian.com or call consultation, we will do our best to solve for you!
(1) advantages and characteristics of centralized processing of wind pipes
①减少材料损耗，降低加工成本：风管集中批量预制加工，能够做到“量体取材”，避免了人工操作时材料乱截、大材小用等现象，使用材料，同时降低人工成本。
(1) Reduce material loss, reduce processing costs: centralized batch prefabrication of air duct, can achieve "volume material", avoid the manual operation of materials in disorder, large materials and small use of such phenomena, the maximum use of materials, while reducing labor costs.
②缩短现场工期：集中加工能形成流水线生产作业，有效提高人员及材料效率，缩短生产周期，提高材料利用率。因集中加工一般在站外加工，所以在现场机电工作面还没有形成的时候，即可提前在场外进行，对于工期紧、任务重的机电安装工程，能有效节省大量现场工作时间和交叉作业时间，节约现场的加工场地，改善地铁施工场地不足的问题。
(2) Shortening the on-site construction period: centralized processing can form a production line, effectively improve the efficiency of personnel and materials, shorten the production cycle, and improve the utilization of materials. Because the centralized processing is usually done outside the station, it can be done out of the field ahead of schedule before the mechanical and electrical working face is formed. For the mechanical and electrical installation projects with tight construction period and heavy tasks, it can effectively save a lot of on-site working time and cross-operation time, save the processing site on the spot, and improve the subway construction site. The question of foot.
(3) Improving the quality by a large margin: The factory processing air duct realizes the modularization, intellectualization, standardization and high efficiency of production, greatly reduces the material error of air duct and improves the appearance quality. (4) Easy overall planning and management: Centralized processing can avoid the good and bad scattered processing capacity of each construction team, and can avoid the problem of inconsistent air duct products caused by different processing technology and standards. At the same time, centralized processing can better control the installation site of safe and civilized construction, to avoid the phenomenon of semi-finished products piled up in disorder.
（2）风管集中化加工的缺点
(2) disadvantages of centralized air duct processing
①风管集中加工后，各站施工队将同时与同一加工厂家进行合作，这将给施工方与加工方在沟通、进度等方面带来挑战，遇到施工高峰期时，如前期准备不足，所有站的生产压力集中到同一厂家，可能会对施工造成影响。
(1) After centralized air duct processing, the construction team of each station will cooperate with the same manufacturer at the same time, which will bring challenges to the construction party and the processing party in communication, progress and other aspects. In the peak period of construction, if the preparation is insufficient, the production pressure of all stations will be concentrated in the same manufacturer, which may affect the construction.
②准备周期长、初期投入大：集中生产如由项目部自筹（或某一施工队自筹），其厂房筹建、场地规划、方案制定等周期较为漫长；初期设备成本大，如不能形成一定规模，难以收回成本。
(2) Long preparation period and large initial investment: if centralized production is self-raised by the project department (or a construction team), the period of workshop preparation, site planning, scheme formulation is relatively long; if the initial equipment costs are large, it is difficult to recover costs if it can not form a certain scale.
③成品运输问题：集中加工后需将风管成品运输各站，这将带来如下影响：
(3) Transportation of finished products: After centralized processing, finished air ducts should be transported to various stations, which will bring the following effects:
a. 风管成品受压后易变形（且不易修复），在运输中装卸车、进站经常会产 生碰压，影响风管美观，甚影响风管质量。
A. The finished air duct is easy to deform (and not easy to repair) after compression. In transportation, loading and unloading trucks and stops often produce impact pressure, affecting the beauty of air duct, and even affecting the quality of air duct.
b. 风管成品比原材料占用的空间大很多，因此会增加运输次数，提高运输 成本，同时因地铁施工一般在市区，如遇限行区域施工时只能晚上进料，给施工带来不便。
B. The finished air duct occupies much more space than the raw material, so it will increase the frequency of transportation and increase the cost of transportation. At the same time, because the subway construction is generally in the urban area, such as restricted traffic area construction can only feed at night, which brings inconvenience to the construction.
有了济南通风管道加工上面的小总结，希望对广大客户有所帮助，如果有什么不理解的或者寻求帮助的请点击我们的网站：http://www.jinanxinlian.com或者来电咨询，我们会尽全力为您解决!
With Jinan ventilation duct processing above a small summary, I hope to help the majority of customers, if there is any incomprehension or seek help, please click our official website: http://www.jinanxinlian.com or call consultation, we will do our best to solve for you!