风管加工的作业条件怎么才算合理？
2018-09-28
空调风管加工的质量直接关系到人体呼吸空气的质量,所以济南空调风管加工必需契合相应的规范.
The quality of air-conditioning duct processing is directly related to the quality of human breathing air, so Jinan air-conditioning duct processing must conform to the corresponding norms.
,空调风管外观质量应到达折角平直,圆弧平均,两端面平行,无翘角,外表凹凸不大于5 mm;风管与法兰衔接结实,翻边平整,宽度不小于6mm,紧贴法兰;风管法兰孔距应契合空调风管加工的设计请求和施工标准的规则,焊接应结实,焊缝处不设置螺孔,螺孔具备互换性;矩形风管边长大于630mm保温风管大于800mm时应有加固措施,角钢加固筋应排列划一、平均对称固定结实.
Firstly, the appearance quality of air-conditioning duct should reach a straight bending angle, arc average, two ends parallel, no warping angle, appearance concave and convex not more than 5 mm; air duct and flange joint is strong, flanged flat, width is not less than 6 mm, close to the flange; air duct flange spacing should meet the air-conditioning duct processing design requirements and construction standards of the rules, welding should be solid, weld seam. The screw holes are interchangeable if no screw holes are set at the place. The rectangular air duct should be strengthened when the length of the air duct is larger than 630 mm and the insulation air duct is larger than 800 mm. The angle steel reinforcement bars should be arranged uniformly and symmetrically and stably.
其次,空调风管加工的划线办法可用直角线法.展开办法采用平行线法.依据大样图风管不同的几何外形和规格,分别划线展开,并停止剪切.下料后在轧口之前,板材必需倒角.
Jinan air duct processing is the most important quality control process, in addition to processing data, processing technology and other aspects, Jinan air conditioning duct processing also has certain operating conditions.
1.集中加工应具有宽阔、亮堂、干净、空中平整、不湿润的厂房.
1. centralized processing should have wide, bright, clean, air leveling, and non wetting workshop.
2.现场分散加工应具有能防雨雪、大风及构造结实的设备,并能保证现场加工场地规整有序.
2. On-site dispersed processing should be equipped with rain-proof, snow-proof, strong wind and structurally strong equipment, and can ensure the orderly processing site.
3.作业地点要有相应加工工艺的根本机具、设备及电源和牢靠的平安防护安装,并配有消防器材.
3. Operating place should have the basic equipment, equipment and power supply of corresponding processing technology, and reliable safety protection installation, and equipped with fire fighting equipment.
4.空调风管加工应有经批准的图纸、经检查的大样图、系统图,并有施工员书面的技术质量及平安交底.只要将空调风管加工的各个方面都控制起来.
4. Air-conditioning duct processing should have approved drawings, large-scale checked drawings, system drawings, and a written technical quality of the construction staff and safe disclosure. As long as all aspects of air-conditioning duct processing are controlled.
更多的关于济南通风管道加工问题或者详细的内容，请进入我们公司的网站：http://www.jinanxinlian.com网站中会有很多的内容仅供参考。
For more information on the processing of Jinan ventilation pipes, please visit our company's website: http://www.jinanxinlian.com. There will be a lot of content for reference only.
The quality of air-conditioning duct processing is directly related to the quality of human breathing air, so Jinan air-conditioning duct processing must conform to the corresponding norms.
,空调风管外观质量应到达折角平直,圆弧平均,两端面平行,无翘角,外表凹凸不大于5 mm;风管与法兰衔接结实,翻边平整,宽度不小于6mm,紧贴法兰;风管法兰孔距应契合空调风管加工的设计请求和施工标准的规则,焊接应结实,焊缝处不设置螺孔,螺孔具备互换性;矩形风管边长大于630mm保温风管大于800mm时应有加固措施,角钢加固筋应排列划一、平均对称固定结实.
Firstly, the appearance quality of air-conditioning duct should reach a straight bending angle, arc average, two ends parallel, no warping angle, appearance concave and convex not more than 5 mm; air duct and flange joint is strong, flanged flat, width is not less than 6 mm, close to the flange; air duct flange spacing should meet the air-conditioning duct processing design requirements and construction standards of the rules, welding should be solid, weld seam. The screw holes are interchangeable if no screw holes are set at the place. The rectangular air duct should be strengthened when the length of the air duct is larger than 630 mm and the insulation air duct is larger than 800 mm. The angle steel reinforcement bars should be arranged uniformly and symmetrically and stably.
其次,空调风管加工的划线办法可用直角线法.展开办法采用平行线法.依据大样图风管不同的几何外形和规格,分别划线展开,并停止剪切.下料后在轧口之前,板材必需倒角.
Secondly, the method of marking the air duct of air conditioner can be used right angle line method, parallel line method. According to the different geometry shape and specification of the air duct of the large sample drawing, the line is drawn separately and the shearing is stopped. After cutting, the sheet must be chamfered before rolling.
Jinan air duct processing is the most important quality control process, in addition to processing data, processing technology and other aspects, Jinan air conditioning duct processing also has certain operating conditions.
1.集中加工应具有宽阔、亮堂、干净、空中平整、不湿润的厂房.
1. centralized processing should have wide, bright, clean, air leveling, and non wetting workshop.
2.现场分散加工应具有能防雨雪、大风及构造结实的设备,并能保证现场加工场地规整有序.
2. On-site dispersed processing should be equipped with rain-proof, snow-proof, strong wind and structurally strong equipment, and can ensure the orderly processing site.
3.作业地点要有相应加工工艺的根本机具、设备及电源和牢靠的平安防护安装,并配有消防器材.
3. Operating place should have the basic equipment, equipment and power supply of corresponding processing technology, and reliable safety protection installation, and equipped with fire fighting equipment.
4.空调风管加工应有经批准的图纸、经检查的大样图、系统图,并有施工员书面的技术质量及平安交底.只要将空调风管加工的各个方面都控制起来.
4. Air-conditioning duct processing should have approved drawings, large-scale checked drawings, system drawings, and a written technical quality of the construction staff and safe disclosure. As long as all aspects of air-conditioning duct processing are controlled.
更多的关于济南通风管道加工问题或者详细的内容，请进入我们公司的网站：http://www.jinanxinlian.com网站中会有很多的内容仅供参考。
For more information on the processing of Jinan ventilation pipes, please visit our company's website: http://www.jinanxinlian.com. There will be a lot of content for reference only.